Search Results

This paper describes a method to simulate underhood temperature distributions in passenger cars. A simplified engine compartment simulation test rig is used to perform measurements with well known boundary conditions to validate the simulation strategy. The measurement setup corresponds to idle without working fan. The aim of this setup is to validate cases with strong natural convection, e.g. thermal soaking. A coupled steady-state CFD run and thermal analysis is undertaken to simulate the temperature distribution in the test rig. Convective heat transfer coefficients and air temperatures are calculated in StarCD™. The radiative and conductive heat transfer is considered in a RadTherm™ analysis. The strong coupling of flow field and wall temperature in buoyancy driven flows requires an iterative process. Calculated temperatures are compared to measured results in order to validate the simulation method as far as possible. Some of the results are reported in this paper.

This paper addresses the use of neat, indigenous biodiesel in advanced Mercedes-Benz passenger cars. Modern, unmodified EU3 Common-Rail diesel engines with second generation common rail technology were used to determine the effects of neat biodiesel on performance and emission characteristics. The biodiesel was made from the seeds of the Jatropha Curcas plant and sourced from the Central Salt and Marine Chemicals Research Institute in Bhavnagar, India. The production of biodiesel and the vehicle tests are part of a PPP project, funded jointly by the DaimlerChrysler AG and the German DEG. The project aims at providing additional jobs and income in rural Indian areas along with reclaiming unused wasteland. The test vehicles were operated for a cumulative 8000 kilometers with an intention to expose the vehicle and fuel to diverse climatic conditions.

The background for the development activities of the motor vehicle industry is strongly influenced by lawmakers, with engine development, in particular, coming under increasing pressure from the requirements of emissions legislation. Demands for CO2 reduction and thus corresponding savings in consumption contrast with regulations which call for compliance with extremely low emission levels, featuring the extreme of zero tailpipe emissions, and alternative low emission levels which make accurate measurement a problem even with current analysis technology. An example of such requirements are the SULEV limits of California law. These standards have given rise to a wide variety of emission control concepts, each of which, however, has certain limitations in its application. In the context of this general setting, the paper shows that the phase directly subsequent to cold start should be focused upon if these ambitious targets are to be reached.

The improvement of DI diesel engines for passenger cars to fulfil pollutant emission limits and lower fuel consumption and noise is closely linked to continued development of the injection system. Today's injection systems demonstrate varying potential in terms of the flexibility of injection parameters for improving mixture formation and combustion. DaimlerChrysler evaluated the potential of different injection systems, looking particularly at the distributor pump, unit injection system and Common Rail system. Based on the results of these investigations, the Common Rail system was selected. The tests presented in this paper were performed on a single-cylinder engine with Common Rail system. They focused on increased rail pressure in combination with different nozzle geometries. The results show significant benefits in NOx/smoke trade off at part load conditions with high EGR rate.

Due to ever soaring fuel costs and even more stringent emission regulations which require more elaborate technical efforts and unfortunately lead to a negative trend on fuel economy as well, todays and future trucking business is extremely challenged. These facts create an urgent requirement for the engine manufacturer to offer an engine with an optimized cost-benefit-ratio for the trucking business. Mercedes-Benz, as the leader in the European commercial vehicle market - of which e. g. high fuel costs, long maintenance intervals and high engine power-to-weight ratios have always been key characteristics - has developed a new class 8 engine for the US market. The MBE 4000 is a 6 cylinder inline engine in the compact size and low weight category, but due to its displacement of 12,8 liters it offers high performance characteristics like heavier big block engines.

The paper describes results from investigating Common Rail (CR) injection in a dedicated optical engine with optimum access to the whole cross section of the engine cylinder through piston. This engine maintains all production-type details of the combustion chamber geometry being crucial to the flow fields required for optimum engine performance. This optical engine is used along with 2D optical diagnostics for temperature, soot and OH as well as spray shadowgraphy to analyze all phases of injection and combustion under virtually real engine conditions. By using special prototype CR injectors, the effects of engine design and operation strategies on ignition, combustion and pollutant formation are studied and controlling parameters are isolated. Special emphasis is devoted to the effects of injector stability, spray symmetry, nozzle geometry, injection rate, pilot injection and swirl effects.

Cold performance is a very important issue for diesel engines. Customers expect their engines to start reliably under all ambient conditions, and to quickly deliver useful power without unacceptable noise or exhaust emissions. In this programme the low ambient temperature cold start performance of two generations of Mercedes-Benz Heavy-Duty diesel engines has been explored. Both are typical of the smaller European Heavy-Duty engine design. The OM364 LA meets Euro 2 emissions legislation using mechanical controls; the OM904 LA is the first evolution of an all-new design to replace the OM364 LA, and features a three-valve cylinder head and high pressure unit-pump injection, with fully electronic controls. Engines were tested in a temperature controlled chamber, using a procedure that studied the first few minutes of operation from cold.

For studying the effects of injection system properties and combustion chamber conditions on the penetration lengths of both the liquid and the vapor phase of fuel injectors in Diesel engines, a holistic injection model was developed, combining hydraulic and spray modeling into one integrated simulation tool. The hydraulic system is modeled by using ISIS (Interactive Simulation of Interdisciplinary Systems), a one dimensional in–house code simulating the fuel flow through hydraulic systems. The computed outflow conditions at the nozzle exit, e.g. the dynamic flow rate and the corresponding fuel pressure, are used to link the hydraulic model to a quasi–dimensional spray model. The quasi–dimensional spray model uses semi–empirical 1D correlation functions to calculate spray angle, droplet history and droplet motion as well as penetration lengths of the liquid and the vapor phases. For incorporating droplet vaporization, a single droplet approach has been used.

In order to fulfill future emissions standards, there is a need for new exhaust-gas aftertreatment concepts, with NOx-emissions reduction in passenger car diesel engines being of particular importance. The NOx storage catalyst is one of the technologies currently under discussion with high NOx conversion potential, and which is under development at DaimlerChrysler for EURO IV standards. With this system, the nitrogen oxides contained in the diesel exhaust gas are stored under lean exhaust-gas conditions and are reduced in the catalyst through an enriched air-fuel ratio of the exhaust-gas and favorable thermal conditions. Hydrocarbons, carbon monoxide and hydrogen are used as reducing agents. DaimlerChrysler has analyzed the effect of sulphur contained in the fuel on the operation of various catalysts during laboratory and engine testing. The sulphur dioxide in the exhaust gas generates sulfates, which remain on the catalyst when nitrate compounds are regenerated briefly.

1 A recent breakthrough in understanding the origin of ion signals from operating combustion engines [12] led to a new approach in integrating advanced ion current sensing into a compact ignition system. Thus it is now possible to continuously monitor mixture, ignition and combustion properties through online ion current recordings via a novel AC technique. In this paper this AC technique is compared to the standard DC technique and its known drawbacks: expensive high voltage components, sensitivity to plug fouling and expensive electronics. The AC technique is based on the specific properties of the electrical field of spark plugs being characterized by a point source with an extreme inhomogeneity of the electrical field due to the small center electrode. This causes a distinct diode characteristic of the ion signal: very low signals for negative voltages and high signals for positive ion sensing voltages, respectively.

The NO distribution in a directly-injected Diesel engine with realistic combustion chamber geometry was investigated with laser-induced fluorescence (LIF) imaging with KrF excimer laser excitation. The highest possible level of selectivity has been ensured using spectrally resolved LIF investigations inside the Diesel engine. To minimize interference from both, oxygen and polycyclic aromatic hydrocarbon (PAH) LIF the NO signal was detected around 237 nm, blue-shifted compared to the excitation wavelength resulting in a background contribution below 10% at the earliest detection timing possible in the engine under study (20°ca after top dead center, TDC). The in-cylinder NO LIF intensities were compared for different injection systems and operating conditions and correlated to variations in pressure traces and soot temperature measurements.

In response to ever more stringent emission limits (EURO IV, SULEV), engine developers are increasingly turning their attention to engine start-up and warm-up phases. Since in this phase the catalytic converter has not yet reached its operating temperature, problems occur especially with regard to hydrocarbon emissions (HC) which are emitted untreated. Secondary air injection represents one option for heating up the catalytic converter more quickly. The engine is operated during the heating up cycle with retarded ignition angles and a rich mixture. Ambient air (secondary air) is injected close to the exhaust valve seat. During the spontaneously occurring post oxidation phase, the reactive exhaust components ignite and heat up the catalytic converter while simultaneously reducing HC. The various processes which affect the post oxidation, are not well known up to now. In order to achieve concrete improvements, detailed knowledge of its influences are necessary.